Showing results: 151 - 165 of 347 items found.
-
RFCI61000-4-6 -
Lisun Electronics Inc.
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Finero OY
This modular battery test system provides for manufacturers versatile testing possibilities. Due to modularity it allows easy configuration of battery testers for a wide range of different power levels.
-
Model 4702 -
Barth Electronics, Inc
The Model 4702 HMM+™ is a completely new tester primarily intended for device level testing and produces a current waveform as specified in the IEC-61000-4-2, from a 50 ohm source impedance system.*This tester provides device level test data that allows users to evaluate the IEC current waveform protection level of their devices. We included failure identification by leakage current increases in the 4702 tester so precise pass/failure levels can be closely measured.*The 4702 HMM+™ provides a new and improved test connection method for making quantifiable and repeatable device level HMM measurements.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Micro Centurion II -
Raytech AG
Raytech Digital Micro ohm meter, Micro-Centurion II, was designed for high degree of accuracy to measure very low resistances. This technology was then packed into a portable test system to be used by apparatus manufacturers, rebuild shops, and electrical maintenance crews. This intelligent system has an easy to use operation screen, which allows quick selection of the current level and resistance level to be measured.
-
1176 -
Draper Tools Ltd
Checks battery charge level and alternator output level. 880mm of insulated cable with test probe and earth (crocodile) clip. For 12V DC systems only. Display packed.Warning: For testing DC circuits on vehicles within the voltage range only. Not suitable for testing mains supply AC circuits.
-
Dotcom-Monitor
A load test is a planned test to perform a specified number of requests to a system in order to test the functionality of the system under specific levels of simultaneous requests. A load test ensures that a web system is capable of handling an expected volume of traffic, and therefore is sometimes referred to as volume testing. The goal of a load test is to prove that a system can handle the expected volume with minimal to acceptable performance degradation. The threshold of acceptable performance degradation must be defined by the testers as some value considered acceptable to the end user so that users will not bounce from the site.
-
ViAcoustics
The Small Device Noise Emission Test System from VIacoustics is a turnkey solution for the measurement of noise emissions of small devices typically used in computers, consumer electronics, appliances and automobiles. The system includes all hardware and software necessary (see the components tab) for the determinations of sound power levels (1/3 octave band and A-weighted), emission sound pressure levels (normalized 1/3 OB, A-weighted and high resolution FFT) and *ISO 532B loudness. The system is designed to be operated by a technician for production level testing or to be used by an engineer in the product development process.
-
Smiths Interconnect
Smiths Interconnect’s test socket and probe card solutions utilize IDI contact technology to ensure superior quality and reliability in semiconductor test applications. Our best-in-class engineering, development and technical expertise ensure support of automated, system level and development test platforms.
-
P.H.D. Family -
Ultra-X INC.
Performs component level motherboard testing utilizing direct hardware-to-hardware communication and displays simple PASS or FAIL results on the system monitor. This mode is used to run tests on a system that successfully completes POST (i.e. the system is capable of displaying a screen when power is on).
-
Megger Group Ltd.
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
Megger Group Ltd.
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
NorCom 2020-WL -
NorCom Systems Inc.
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
MS 1123 -
Meltronics Systemtech
Configurable Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out card level testing for satellite systems (12 different types of boards). The purpose of ATE is to provide a user-friendly environment to test the boards for their functionality, perform specific tests of each card. The card level testing facilitates troubleshooting down to a faulty signal flow path. Both hardware and software designed such a way that each Input / Output is configurable and user can dynamically script the test procedure using standard ‘C’ Language.
-
RedViking
Customers in automotive and off-highway vehicle production and R&D environments trust us to design and build precise, reliable, and repeatable drivetrain component test stands. All of our systems are designed to provide the highest level of dynamic testing capability at a competitive price. For decades, RedViking has designed, built, and implemented highly engineered test systems for drivetrain systems and components.
-
HIACC Engineering & Services Pvt. Ltd.
Inline shock test system simulates a real shock environment to estimate the impact resistance or damage level of a product. The simulated environment replicates shocks produced during product handling, stacking shelves, loading/unloading and transportations. The incline shock test system is widely used in the packaging industry, scientific research institutions and transportation industry.